You can have one RAID 0 or 1 setup and two independent SATA drives, two RAID 0 or 1 sets, or a single RAID 0+1 set. The card comes with an optional RAID utility, which lets you configure a RAID 0, RAID 1, or RAID 0+1 setup on two or more of the SATA ports. However, as long as you have an open PCI slot, you can add this adapter card, which gives you 2 SATA-2 (1.5 Gbps) ports, so you can use the newer drives.
Why throw away your old PC just because you need a new drive and cannot find a good PATA IDE drive for it? Add four independent SATA-I ports to your PCI equipped computer and enjoy the benefits of the optional software RAID configuration for added speed and/or data security with this adapter card from Monoprice! With SATA being the standard for the past few years, it is getting harder and harder to find a good PATA IDE drive for older computers. Výrobek je dodáván s manuálem pouze v anglickém nebo německém jazyce.Item: 122439847830 Silicon Image SATA Link 2 Port SATA/RAID PCI Interface card Sil3112ACT144.
SPMH3726 is equipped with a "SCSI I 50pin Low Density Centronics Connector" like bracket to be mounted in a standard enclosure to provide the immediate upgrade of your storage system.
With its unique data aggregation and 3Gbps serial link capacity, it supports 5 SATA or SATA2 device with auto-negotiation features over one single eSATA connector. It is designed to provide a high performance link between a single SATA2 host port and 5 SATA device ports. Enclosure Management SEMB (I2C bus) support performance greater than 220MB/s (RAID 0) eSATA signal level support (1m and 2m PHY compliant) Four SATA device ports, 1.5Gb/s and 3Gb/s eSATA signal level suppport (1m and 2m PHY compliant) Supports PM aware hosts and non-PM aware
Supports one SATA host port, 1.5Gb/s and 3Gb/s MH3726 delivers the performance and connectivity required for servers and I/O demanding applications such as CD-ROM servers, Video-On-Demand (digital content and high-definition video), database servers, workstations, high-end desktops, software RAID sub systems, and image systems. Other important features include, programmable high drive capability for backplane and external applications, asynchronous notification to eliminate the need for host polling to determine if a device has been added or removed, and hot plug support.Ĭoupling with proper host controllers such as Silicon Image Sil3124, Sil3132 and Marvell 88SE6145, SPMH3726 - SATA II port multiplier, a high reliable and extremely fast variety of storage applications (RAID 0, 1, 5, 10, Concatenated and JBOD). Additionally, the SPMH3726 contains a SATA enclosure management bridge (SEMB) to pass in-band enclosure management information between the host and an enclosure management device. The SPMH3726 supports host and device link rates of 1.5Gbps and 3Gbps with auto-negotiation allowing system designers to utilize 3Gbps host links with today?s 1.5Gbps hard drives, and to futureproof designs for the emergence of 3Gbps SATA hard drives.
Additionally, the feature-rich SPMH3726 supports all the port multiplier related SATA II extensions allowing system designers to exploit the full potential of SATA in their storage solutions. With its unique data aggregation capability and 3Gbps serial link capability, the SPMH3726 is able to take full advantage of 3Gbps host link bandwidth and FIS-based switching host controllers by bundling together data from device ports and sending it over the 3Gbps host link. SPMH3726 is 1-to-5 SATA Port Multiplier designed to provide a high performance link between a single SATA host port and 5 SATA device ports. Supports host control of hard disk drive staggered spin-upĪll ports support hot plug and extended (48 bit LBA) drive capability.įeatures independent 8 KByte FIFO per Device Serial ATA channel for reads and writesĬoupling with SATA2-PCIE02 or SATA2-PCIX01 to support RAID Function (RAID 0, 1, 5, 10, Concatenated and JBOD). Supports host and device link rates of 1.5Gbps and 3Gbps with auto-negotiation One to Five SATA Port Multiplier (SCSI I 50pin Low Density Centronics Connector Form Factor)įull support for FIS-based switching and command-based switching SATA host controllers